Structural Fire Damage Cleaning in Trumann, AR
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. The question is which members can be cleaned, which need a sister, and which have to come out. Unify Fire Solutions puts you in touch with independent, licensed and insured Trumann contractors who clean the bare structure down to sound wood.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Cleaned wood encapsulated against lingering odor
What Makes Framing Work Different
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
A real person answers around the clock, and the search for a crew begins on that call. Timing depends on which crews near Trumann are free, and it is often the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Burned joists and decking can fail under one person's weight, and open wiring may still carry current. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Structural Cleaning Services From Rafters to Slab
This is not contents cleaning and it is not debris haul-out. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
For a few blackened studs or a small closet fire, wire brushes, sanding discs and a HEPA-shrouded grinder may be all it takes. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. A smoke-stained or wet vapor barrier usually comes out and goes back new.
Have the contractor explain the method they plan for each part of the house. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Plan for containment, because blasting throws soot and media into every corner it can reach. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask what the plan is to shield the undamaged rooms, floors and glass.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Trumann. It costs nothing to call.
Call +1-833-336-1630The Path From Charred Framing to Sealed Wood
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Let us know if an adjuster, engineer or roofer has already visited.
- 2
Mobile Crew on Site
The contractor arrives with a compressor, blasting equipment and containment materials. First they confirm the roof deck and floors will hold weight and that the exposed circuits are dead.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
Once the wood is blasted, vacuumed and sealed, the crew lead walks you through the open structure. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. Two rafters were cut deep enough that they called in an engineer, and those got sistered.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. Soda blasting and a coat of sealer saved most of the wall.
Our basement fire blackened the block walls and the steel beam over the family room. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. The basement smells normal again, even closed up.
Your Structural Fire Cleaning Questions Answered
How do crews decide if a charred stud can stay?
They probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Deep char, cracks or a reduced cross section mean sistering or replacement, with a structural engineer making the call on anything questionable.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. It is common to see both on one job.
Why seal the framing if it has already been cleaned?
Smoke gets deep into the pores of the wood, past what blast media can reach. An encapsulating sealer traps what is left so the odor does not seep back through the finished walls. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Blown-in and batt insulation trap smoke and soot like a filter, and many get soaked by hose water too. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Expect alkaline detergents and scrub brushes for light staining and media blasting for thick deposits. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
You may not on a small job, but any doubtful load-bearing member calls for one. An engineer's report on trusses, headers, beams, steel and badly charred joists protects you and supports the claim. The building department may ask for it before signing off on the rebuild.
Structural Fire Cleaning Throughout Trumann
Calls come in from all over Trumann and nearby towns, from older homes with solid lumber framing to newer builds with engineered trusses and I-joists. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Do not let the rebuild close walls over dirty framing.
